PNEUMATIC RECLAIM UNITS

Hensley offers Pneumatic Reclaim Bodies and Trailers for those companies that need to reclaim the feed after a house has been emptied.  With proven results, our system was designed through our in-house Design and Engineering staff.  Our use of Newer Blower Technology allows a higher CFM (Cubic Feed per Minute) at a lower Engine RPM.  Hensley by far has the highest quality pneumatic reclaim units on the market!  Also available are Tow Behind Reclaim Vac Trailers, Grain Vacs and Mill Clean-up Vacs!

 

Features: 
  • Gardner/Denver Blower - Mounted On Trailer
  • AWS 101 8-Vane Air Lock
  • Stainless Steel Cyclone and Dust Collector
  • View Windows on Cyclone and Dust Collector
  • Air Operated Diverter Valves In Each Compartment (With Front Compartment as "Default")
  • Blower Filter with Filter Monitor Gauge
  • (3) 20' Long Galvanized Flex Hoses
  • Heat Exchanger
  • Hendrickson INTRAXX 25,000 lb. Suspensions
  • 102" Wide Track Axles
  • Truck-Lite/S.S. LED Lighting
  • Hot Dipped Galvanized Subframe & Kingpin Plate (Standard)
  • Huck Fasteners On Subframe & Kingpin Plate
  • Machine Welded Seams
  • 3/8” Long Sills - 5086 Tanker/Trailer Aluminum
  • 1/2” Thick End Plates - 6061 Aluminum Plate
  • 1/8” Thick Side Wall And Dividers - 5052-H32 Aircraft Grade Aluminum
  • 4” Extruded Aluminum Load Bearing Channels At Top Of Tank
  • Floor U-Trough,  Aluminum Construction
  • Aluminum Manual Gate Controls On Each Compartment
  • All Hydraulic Auger System
  • Generation II Auger System - Spring Mounted Motors to reduce Spline Wear
  • Parker Direct Drive Motors with 1 1/4"  Spline Shafts
  • 25 Ft. Long Discharge Auger With Support Truss
  • Steel Parts Primed with Epoxy Primer and PPG Mountain Mist Acrylic Enamel
  • Sloped Auger Flighting With 2” I.D. Sch. 80 Pipe - REDUCES PRODUCT DAMAGE
  • Split Woodblock Bearings in Discharge and Floor Auger
  • Heavy Duty Hydraulic Motor on Floor Auger - Mounted At The Rear
  • Variable Speed Control On Floor Auger
  • 50-1 Superior Gearbox - Single # 80 Roller Chain
  • Turning Device Relief Valves (Gearbox  And Chain Protection)
  • Valve Bank With Lock Valve On Boom Cylinder
  • Hydraulic Controls located at Rear Driver’s Side
  • Rear Ladder, Center Mount
  • Rear Tray Safety Bar At Rear of Body
  • Truck-Lite Completely Sealed Wiring System - All wiring run through Rubber Grommets - No Cuts Or Splices!
  • 50th Anniversary "v" Shaped Aluminum Bumper With (2) Sets of Four Lights - RED-RED-RED-AMBER
  • Impact Absorbing Bumper At Rear
  • High Mount Stop/Turn Lights - (1) Red, (1) Amber
  • Hensley Logo/American Flag Anti-Sail Mud flaps
  • Aluminum Mud Guards Ahead of Tandems
  • Conspicuity Tape
  • 10' Front & Rear Aluminum Fenders - Both Sides
Options: 
Rice Lake On-Board Scale System
On Board Scale Ticket Printer (For Rice Lake Scales)
Pneumatic Reclaim Systems
Pneumatic Reclaim Systems
Pneumatic Reclaim Systems
Pneumatic Reclaim Systems
Pneumatic Reclaim Systems
Pneumatic Reclaim Systems